linux 添加永久ip、路由和开启路由功能
一、添加永久ip
编辑/etc/sysconfig/network-scripts/ifcfg-eth0文件:
网络接口配置文件
[root@localhost ~]# cat /etc/sysconfig/network-scripts/ifcfg-eth0
# Intel Corporation 82545EM Gigabit Ethernet Controller (Copper)
TYPE=Ethernet #网卡类型
DEVICE=eth0 #网卡接口名称
ONBOOT=yes #系统启动时是否自动加载
BOOTPROTO=static #启用地址协议 --static:静态协议 --bootp协议 --dhcp协议
IPADDR=192.168.1.11 #网卡IP地址
NETMASK=255.255.255.0 #网卡网络地址
GATEWAY=192.168.1.1 #网卡网关地址
DNS1=10.203.104.41 #网卡DNS地址
HWADDR=00:0C:29:13:5D:74 #网卡设备MAC地址
BROADCAST=192.168.1.255 #网卡广播地址
重新导入ifcfg-eth0网络配置文件
[root@localhost ~]# /etc/init.d/network reload
Shutting down interface eth0: [ OK ]
Shutting down loopback interface: [ OK ]
Bringing up loopback interface: [ OK ]
Bringing up interface eth0: [ OK ] 网卡接口关闭与激活
[root@localhost ~]# ifdown eth0 #关闭网络
[root@localhost ~]# ifup eth0 #启动网络 网络服务启动与关闭
方法一:
[root@localhost ~]# service network stop #关闭网络服务
[root@localhost ~]# service network start #启动网络服务
[root@localhost ~]# service network restart #重启网络服务
方法二:
[root@localhost ~]# /etc/init.d/network stop
[root@localhost ~]# /etc/init.d/network start
[root@localhost ~]# /etc/init.d/network restart
网卡状态查询
[root@localhost ~]# service network status
Configured devices:
lo eth0
Currently active devices:
lo eth0 临时配置网卡信息,无需重启。
[root@localhost ~]# ifconfig eth0 10.1.1.10 netmask 255.0.0.0
查看网卡接口信息,默认列出所有接口
[root@localhost ~]# ifconfig
eth0 Link encap:Ethernet HWaddr 00:0C:29:13:5D:74
inet addr:192.168.1.11 Bcast:192.168.1.255 Mask:255.255.255.0
inet6 addr: fe80::20c:29ff:fe13:5d74/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:413 errors:0 dropped:0 overruns:0 frame:0
TX packets:572 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:47701 (46.5 KiB) TX bytes:64842 (63.3 KiB)
Base address:0x2000 Memory:d8920000-d8940000 lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:407 errors:0 dropped:0 overruns:0 frame:0
TX packets:407 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:70759 (69.1 KiB) TX bytes:70759 (69.1 KiB)
查看当前路由及网关信息
[root@localhost ~]# netstat -r
Kernel IP routing table
Destination Gateway Genmask Flags MSS Window irtt Iface
192.168.1.0 * 255.255.255.0 U 0 0 0 eth0
169.254.0.0 * 255.255.0.0 U 0 0 0 eth0
default 192.168.1.1 0.0.0.0 UG 0 0 0 eth0 DNS:
主机名:CentOS
主DNS:202.106.46.151
第二DNS:202.106.0.20
第三DNS:8.8.8.8 网络配置:
eth0
静态ip:192.168.1.106
子网掩码 255.255.255.0
默认网关 IP 192.168.1.1 DEVICE=eth0
IPADDR=192.168.1.106
NETMASK=255.255.255.0
BROADCAST=192.168.1.255
ONBOOT=yes
BOOTPROTO=none
GATEWAY=192.168.1.1
TYPE=Ethernet
"/etc/sysconfig/network-scripts/ifcfg-eth0" 11L, 187C
二、设置永久路由的方法:
1.在/etc/rc.local里添加
方法:
route add -net 192.168.3.0/24 dev eth0
route add -net 192.168.2.0/24 gw 192.168.2.254 2.在/etc/sysconfig/network里添加到末尾
方法:GATEWAY=gw-ip 或者 GATEWAY=gw-dev 3./etc/sysconfig/static-routes : (没有static-routes的话就手动建立一个这样的文件)
any net 192.168.3.0/24 gw 192.168.3.254
any net 10.250.228.128 netmask 255.255.255.192 gw 10.250.228.129
三、开启永久路由转发功能
编辑/etc/sysctl.conf配置文件
linux 添加永久ip、路由和开启路由功能的更多相关文章
- linux 添加secondary ip
linux下ip地址除了primary外,还有两种:1. ip alias(子接口)2. secondary ip(辅助ip) 都可在一块物理网卡上添加,alias由ifconfig添加,ifconf ...
- Linux添加永久路由的方法
通常我们使用route add -net添加临时路由.当系统重启,临时路由将丢失,重新配置路由带来了不必要的麻烦.可通过固化临时路由为永久路由的方法解决该问题. static-routes文件为路由固 ...
- Linux添加永久静态路由
1.首先查看一下本机的路由 route -n 2.比如我们添加两条静态路由,访问192.168.142.100时通过192.168.142.10:访问192.168.142.200时通过192.168 ...
- Linux下修改IP、DNS、路由命令行设置
本文最后修改时间:20180313 一.快速修改,重启后设置就没了 ifconfig eth0 192.168.1.22 netmask 255.255.255.0 up route add defa ...
- linux配置永久ip不生效解决方法
本文原文来自 http://blog.csdn.net/zymx14/article/details/51472239 linux下使用ifconfig eth0 ip地址可以设置ip地址 ,命令为: ...
- linux 添加静态ip dns
/etc/network 下:interfaces auto loiface lo inet loopbackauto eth0iface eth0 inet staticaddress 192.16 ...
- 原 linux添加虚拟ip(手动vip和keepalived方式)
https://blog.csdn.net/dear_snowing/article/details/68066544 https://www.cnblogs.com/liuyisai/p/59906 ...
- linux route命令的使用详解 添加永久静态路由 tracert traceroute
linux route命令的使用详解 添加永久静态路由 tracert traceroute route -n Linuxroute print Windows traceroute ...
- 关于linux的添加永久静态路由的static-routes方法
一:使用 route 命令添加 使用route 命令添加的路由,机器重启或者网卡重启后路由就失效了,方法: //添加到主机的路由 # route add –host 192.168.1.11 dev ...
随机推荐
- Proc-fs 编程
一.简介 Proc文件系统是Linux系统上的一种伪文件系统(也即虚拟文件系统),存储的是当前内核运行状态的一系列特殊文件,用户可以通过这些文件查看有关系统硬件及当前正在运行进程的信息,甚至可以通过更 ...
- Hive2 jdbc test
package andes; import java.io.BufferedWriter; import java.io.FileOutputStream; import java.io.IOExce ...
- openfire+asmack搭建的安卓即时通讯(五) 15.4.12
这一篇博客其实是要昨天写的,但昨天做了作修改就停不下来了,这次的修改应该是前期开发的最终回了,其余的功能有空再做了,下周可能要做一些好玩的东西,敬请期待! 1.修改下Logo:(Just We) ht ...
- 使用Burpsuite破解Webshell密码
Burp Suite 是用于攻击web 应用程序的集成平台.它包含了许多工具,并为这些工具设计了许多接口,以促进加快攻击应用程序的过程.所有的工具都共享一个能处理并显示HTTP 消息,持久性,认证 ...
- codeforces 487B B. Strip(RMQ+二分+dp)
题目链接: B. Strip time limit per test 1 second memory limit per test 256 megabytes input standard input ...
- python刷题专用函数。。
无它,非bin()莫属. bin(x) Convert an integer number to a binary string. The result is a valid Python expre ...
- canvas仿屏幕保护运动线条
canvas是H5中及其重要的一个新标签,它得出现不仅让前端做图形图表功能变得异常强大,还用极强的性能丰富前端渲染页面的能力. Life is not a problem to be solved, ...
- hammer.js中文文档
转自:http://www.uedsc.com/hammerjs-api.html HammerJS是一个优秀的.轻量级的触屏设备手势库,现在已经更新到2.04版本,跟1.0版本有点天壤地别了,毕竟改 ...
- 22Spring_JdbcTemplatem模板工具类的使用——使用外部属性文件来配置(properties)
前一篇文章写得是xml文件来配置数据库连接的.但是为了方便,我们实际中采用的是properties文件的方式来配置数据库的.修改properties 文件 会比 修改 xml文件 方便. 做法是: 将 ...
- php基础05:常量
<?php // 1.PHP 常量介绍 // 常量是单个值的标识符(名称).在脚本中无法改变该值.有效的常量名以字符或下划线开头(常量名称前面没有 $ 符号). // 2设置 PHP 常量 // ...
