Arduino通过I2C(SSD1306)驱动0.96寸12864OLED

I²C驱动的128x64 OLED

I²C (Inter-Integrated Circuit) 集成电路总线是I2CBus的简称, 是一种串行通信总线, 使用多主从架构. 飞利浦公司在1980年代为了让主板, 嵌入式系统或手机用以连接低速周边设备而发展. I²C的正确读法为"I-squared-C"。
I²C只使用两条双向漏极开路(Open Drain): 串行数据SDA及串行时钟频率SCL总线, 且利用上拉电阻将两条总线的电位上拉. I²C允许相当大的工作电压范围, 但典型的电压准位为+3.3V或+5V. I²C的参考设计使用一个7bit长度的地址空间但保留了16个地址, 所以在一组总线最多可和112个节点通信. 常见的I2C总线依传输速率的不同而有不同的模式: 标准模式100 Kbit/s, 低速模式10 Kbit/s, 但时钟频率可被允许下降至零, 这代表可以暂停通信. 而新一代的I²C总线可以和更多的节点(支持10比特长度的地址空间)以更快的速率通信: 快速模式400 Kbit/s, 高速模式3.4 Mbit/s.
在单片机中使用I²C通信协议的时候, 需要编写程序去模拟I²C总线的通信, 对于I²C通信协议需要补充的一点是: 在实际通信传输数据时, SCL总线拉高的时间只要大于1.5μs都能够正常传输数据.

这块128x64 OLED的裸屏是由SSD1306驱动的. 该芯片专为共阴极 OLED 面板设计, SSD1306 中嵌入了对比度控制器, 显示 RAM 和晶振, 并因此减少了外部器件和功耗. 有 256级亮度控制, 数据/命令的发送有三种接口可选择: 6800/8000串口, I²C接口或 SPI 接口. 适用于多数简单的应用, 移动电话的屏显, MP3播放器和计算器等.

SSD1306本身支持多种总线驱动方式包括SPI以及并口等, 通过芯片的相应IO口拉低拉高来选择哪一种接口. 模块通过电阻将相应IO口配置固化使用了I²C接口方式，但可能你买到的同样的驱动芯片的模块会采用其他接口. 使用I2C接口时, SSD1306允许有最多两个7位的I2C地址, 同样通过相应的IO口拉低拉高来切换, 一般默认是0x3C. 在有些模块(不是所有, 有些PCB没有预留)的背面, 可以看到I²C地址选项提示, 需要改变模块I²C地址时只需要把提示位置的电阻取下焊接到另外一端即可. 要注意的是版上的I²C地址是加上了第零位读写位后的数值,
0x78 = 0x3c << 1 (0111 1000 ---- 0011 1100)
0x7A = 0x3d << 1 (0111 1010 --- 0011 1101)

SSD1306的从机地址

SSD1306 在发送或接受任何信息之前必须识别从机地址. 设备将会响应从机地址, 后面跟随着从机地址位(SA0 位)和读写选择位(R/W#位),格式如下:

b7  b6  b5  b4  b3  b2  b1   b0

                  SA0  R/W#

SA0 位为从机地址提供了一个位的拓展, 0111100 或 0111101 都可以做为 SSD1306 的从机地址. D/C#引脚作为 SA0 用于从机地址选择. R/W#为用来决定 I2C 总线接口的操作模式. R/W# = 1,读模式, R/W# = 0 写模式

安装Library

1. Adafruit_SSD1306
2. Adafruit-GFX-Library

修改Adafruit_SSD1306.h

设置正确的液晶分辨率, 将其中的SSD1306_128_64反注释, 将SSD1306_128_32注释掉

//   #define SSD1306_128_64

   #define SSD1306_128_32

//   #define SSD1306_96_16

运行SSD1306 Example

例子 - 输出直线和文字以及文字滚动, 例子中能明显看出文字滚动时参数的含义

#include <SPI.h>

#include <Wire.h>

#include <Adafruit_GFX.h>

#include <Adafruit_SSD1306.h>

#define OLED_RESET 4

Adafruit_SSD1306 display(OLED_RESET);

#if (SSD1306_LCDHEIGHT != 64)

#error("Height incorrect, please fix Adafruit_SSD1306.h!");

#endif

void setup() {

  Serial.begin();

  display.begin(SSD1306_SWITCHCAPVCC, 0x3C);  // initialize with the I2C addr 0x3C (for the 128x64)

  display.display();

  delay();

}

void loop() {

  display.clearDisplay();

  testdrawline();

  delay();

  display.clearDisplay();

  testdrawchar();

  delay();

  display.clearDisplay();

  testdrawchar2();

  delay();

  display.clearDisplay();

  testscrolltext();

  delay();

}

void testdrawline() {

  for (int16_t i=; i<display.width(); i+=) {

    // x1 y1 x2 y2

    display.drawLine(i, , i, display.height(), WHITE);

    display.display();

    delay();

  }

  delay();

  display.clearDisplay();

  for (int16_t i=; i<display.height(); i+=) {

    display.drawLine(, i, display.width(), i, WHITE);

    display.display();

    delay();

  }

}

void testdrawchar(void) {

  display.setTextSize();

  display.setTextColor(WHITE);

  display.setCursor(,);

  for (uint8_t i=; i < ; i++) {

    if (i == '\n') continue;

    display.write(i);

    if ((i > ) && (i %  == ))

      display.println();

  }

  display.display();

  delay();

}

void testdrawchar2(void) {

  display.setTextSize();

  display.setTextColor(WHITE);

  uint8_t j = ;

  for (uint8_t l=; l < ; l++) {

    display.setCursor(,l*);

    for (uint8_t i=; i < ; i++) {

      j++;

      if (j == '\n') continue;

      display.write(j);

      display.display();

      delay();

    }

  }

}

void testscrolltext(void) {

  testdrawchar();

  delay();

  // startscrollright(uint8_t start, uint8_t stop)

  // Activate a scroll to the right for rows start through stop The display is 16 rows tall. To scroll the whole display, run: display.scrollright(0x00, 0x0F)

  // Parameters: start First row to scroll, stop  Last row to scroll

  display.startscrollright(0x00, 0x02);

  delay();

  display.startscrollright(0x03, 0x05);

  delay();

  display.stopscroll();

  delay();

  // Activate a scroll to the left for rows start through stop The display is 16 rows tall. To scroll the whole display, run: display.startscrollright(0x00, 0x0F)

  display.startscrollleft(0x00, 0x05);

  delay();

  display.startscrollleft(0x00, 0x0F);

  delay();

  display.stopscroll();

  delay();

  // Activate a scroll to the upper right for rows start through stop The display is 16 rows tall.

  display.startscrolldiagright(0x00, 0x03);

  delay();

  display.startscrolldiagright(0x00, 0x07);

  delay();

  // Activate a scroll to the upper left for rows start through stop The display is 16 rows tall.

  display.startscrolldiagleft(0x00, 0x03);

  delay();

  display.startscrolldiagleft(0x00, 0x07);

  delay();

  display.stopscroll();

}

例子 - 输出位图(及汉字位图)

#include <SPI.h>

#include <Wire.h>

#include <Adafruit_GFX.h>

#include <Adafruit_SSD1306.h>

#define OLED_RESET 4

Adafruit_SSD1306 display(OLED_RESET);

#if (SSD1306_LCDHEIGHT != 64)

#error("Height incorrect, please fix Adafruit_SSD1306.h!");

#endif

#define NUMFLAKES 5

#define XPOS 0

#define YPOS 1

#define DELTAY 2

#define LOGO16_GLCD_HEIGHT 16

#define LOGO16_GLCD_WIDTH  16

static const unsigned char PROGMEM logo16_glcd_bmp[] =

{ B00000000, B11000000,

  B00000001, B11000000,

  B00000001, B11000000,

  B00000011, B11100000,

  B11110011, B11100000,

  B11111110, B11111000,

  B01111110, B11111111,

  B00110011, B10011111,

  B00011111, B11111100,

  B00001101, B01110000,

  B00011011, B10100000,

  B00111111, B11100000,

  B00111111, B11110000,

  B01111100, B11110000,

  B01110000, B01110000,

  B00000000, B00110000 };

//中文：实

static const unsigned char PROGMEM str_1[] = {

0x02,0x00,0x01,0x00,0x7F,0xFE,0x40,0x02,0x88,0x84,0x04,0x80,0x04,0x80,0x10,0x80,

0x08,0x80,0x08,0x80,0xFF,0xFE,0x01,0x40,0x02,0x20,0x04,0x10,0x18,0x08,0x60,0x04

};

//中文：验

static const unsigned char PROGMEM str_2[] = {

0x00,0x20,0xF8,0x20,0x08,0x50,0x48,0x50,0x48,0x88,0x49,0x04,0x4A,0xFA,0x7C,0x00,

0x04,0x44,0x04,0x24,0x1D,0x24,0xE4,0xA8,0x44,0x88,0x04,0x10,0x2B,0xFE,0x10,0x00

};

//中文：室

static const unsigned char PROGMEM str_3[] = {

0x02,0x00,0x01,0x00,0x7F,0xFE,0x40,0x02,0x80,0x04,0x3F,0xF8,0x04,0x00,0x08,0x20,

0x1F,0xF0,0x01,0x10,0x01,0x00,0x3F,0xF8,0x01,0x00,0x01,0x00,0xFF,0xFE,0x00,0x00

};

void setup() {

  Serial.begin();

  display.begin(SSD1306_SWITCHCAPVCC, 0x3C);  // initialize with the I2C addr 0x3C (for the 128x64)

  display.display();

  delay();

}

void loop() {

  display.clearDisplay();

  display.drawBitmap(, ,  logo16_glcd_bmp, , , WHITE);

  display.display();

  delay();

  display.drawBitmap(, ,  logo16_glcd_bmp, , , BLACK);

  display.display();

  delay();

  display.drawBitmap(, ,  logo16_glcd_bmp, , , WHITE);

  display.display();

  delay();

  display.clearDisplay();

  display.drawBitmap(, , str_1, , , WHITE);

  display.drawBitmap(, , str_2, , , WHITE);

  display.drawBitmap(, , str_3, , , WHITE);

  display.display();

  delay();

  display.clearDisplay();

  testdrawbitmap(logo16_glcd_bmp, LOGO16_GLCD_HEIGHT, LOGO16_GLCD_WIDTH);

}

void testdrawbitmap(const uint8_t *bitmap, uint8_t w, uint8_t h) {

  uint8_t icons[NUMFLAKES][];

  // initialize

  for (uint8_t f=; f< NUMFLAKES; f++) {

    icons[f][XPOS] = random(display.width());

    icons[f][YPOS] = ;

    icons[f][DELTAY] = random() + ;

    Serial.print("x: ");

    Serial.print(icons[f][XPOS], DEC);

    Serial.print(" y: ");

    Serial.print(icons[f][YPOS], DEC);

    Serial.print(" dy: ");

    Serial.println(icons[f][DELTAY], DEC);

  }

  while () {

    // draw each icon

    for (uint8_t f=; f< NUMFLAKES; f++) {

      display.drawBitmap(icons[f][XPOS], icons[f][YPOS], bitmap, w, h, WHITE);

    }

    display.display();

    delay();

    // then erase it + move it

    for (uint8_t f=; f< NUMFLAKES; f++) {

      display.drawBitmap(icons[f][XPOS], icons[f][YPOS], bitmap, w, h, BLACK);

      // move it

      icons[f][YPOS] += icons[f][DELTAY];

      // if its gone, reinit

      if (icons[f][YPOS] > display.height()) {

        icons[f][XPOS] = random(display.width());

        icons[f][YPOS] = ;

        icons[f][DELTAY] = random() + ;

      }

    }

   }

}

控制OLED对比度

初始化

    #include <Wire.h>

    #include <Adafruit_GFX.h>

    #include <Adafruit_SSD1306.h>

    Adafruit_SSD1306 oledDisplay(OLED_MOSI, OLED_CLK, OLED_DC, OLED_RESET, OLED_CS);

自定义方法

void setContrast(Adafruit_SSD1306 *display, uint8_t contrast) {

    display->ssd1306_command(SSD1306_SETCONTRAST);

    display->ssd1306_command(contrast);

}

然后通过这个方法控制,

    setContrast(&oledDisplay, );  //contrast is a number between 0 and 255. Use a lower number for lower contrast

实际测试效果看, contrast为0的时候依然很亮, 数字稍大一些就和255一样亮了.
.

使用U8g2输出中文

安装library: U8g2

在Example里有PrintUTF8例子, 里面有中文输出, 注意: 这个并非所有汉字都能输出. 根据自己的硬件, 取消对应的注释

#include <Arduino.h>

#include <U8g2lib.h>

#ifdef U8X8_HAVE_HW_SPI

#include <SPI.h>

#endif

#ifdef U8X8_HAVE_HW_I2C

#include <Wire.h>

#endif

/*

  U8glib Example Overview:

    Frame Buffer Examples: clearBuffer/sendBuffer. Fast, but may not work with all Arduino boards because of RAM consumption

    Page Buffer Examples: firstPage/nextPage. Less RAM usage, should work with all Arduino boards.

    U8x8 Text Only Example: No RAM usage, direct communication with display controller. No graphics, 8x8 Text only.

*/

// Please UNCOMMENT one of the contructor lines below

// U8g2 Contructor List (Frame Buffer)

// The complete list is available here: https://github.com/olikraus/u8g2/wiki/u8g2setupcpp

// Please update the pin numbers according to your setup. Use U8X8_PIN_NONE if the reset pin is not connected

//U8G2_NULL u8g2(U8G2_R0);    // null device, a 8x8 pixel display which does nothing

//U8G2_SSD1306_128X64_NONAME_F_4W_SW_SPI u8g2(U8G2_R0, /* clock=*/ 13, /* data=*/ 11, /* cs=*/ 10, /* dc=*/ 9, /* reset=*/ 8);

//U8G2_SSD1306_128X64_NONAME_F_4W_HW_SPI u8g2(U8G2_R0, /* cs=*/ 12, /* dc=*/ 4, /* reset=*/ 6);    // Arduboy (Production, Kickstarter Edition)

//U8G2_SSD1306_128X64_NONAME_F_4W_HW_SPI u8g2(U8G2_R0, /* cs=*/ 10, /* dc=*/ 9, /* reset=*/ 8);

//U8G2_SSD1306_128X64_NONAME_F_3W_SW_SPI u8g2(U8G2_R0, /* clock=*/ 13, /* data=*/ 11, /* cs=*/ 10, /* reset=*/ 8);

//U8G2_SSD1306_128X64_NONAME_F_HW_I2C u8g2(U8G2_R0, /* reset=*/ U8X8_PIN_NONE);

//U8G2_SSD1306_128X64_ALT0_F_HW_I2C u8g2(U8G2_R0, /* reset=*/ U8X8_PIN_NONE);   // same as the NONAME variant, but may solve the "every 2nd line skipped" problem

//U8G2_SSD1306_128X64_NONAME_F_SW_I2C u8g2(U8G2_R0, /* clock=*/ 13, /* data=*/ 11, /* reset=*/ 8);

U8G2_SSD1306_128X64_NONAME_F_SW_I2C u8g2(U8G2_R0, /* clock=*/ SCL, /* data=*/ SDA, /* reset=*/ U8X8_PIN_NONE);   // All Boards without Reset of the Display

//U8G2_SSD1306_128X64_NONAME_F_SW_I2C u8g2(U8G2_R0, /* clock=*/ 16, /* data=*/ 17, /* reset=*/ U8X8_PIN_NONE);   // ESP32 Thing, pure SW emulated I2C

//U8G2_SSD1306_128X64_NONAME_F_HW_I2C u8g2(U8G2_R0, /* reset=*/ U8X8_PIN_NONE, /* clock=*/ 16, /* data=*/ 17);   // ESP32 Thing, HW I2C with pin remapping

//U8G2_SSD1306_128X64_NONAME_F_6800 u8g2(U8G2_R0, 13, 11, 2, 3, 4, 5, 6, A4, /*enable=*/ 7, /*cs=*/ 10, /*dc=*/ 9, /*reset=*/ 8);

//U8G2_SSD1306_128X64_NONAME_F_8080 u8g2(U8G2_R0, 13, 11, 2, 3, 4, 5, 6, A4, /*enable=*/ 7, /*cs=*/ 10, /*dc=*/ 9, /*reset=*/ 8);

//U8G2_SSD1306_128X64_VCOMH0_F_4W_HW_SPI u8g2(U8G2_R0, /* cs=*/ 10, /* dc=*/ 9, /* reset=*/ 8);    // same as the NONAME variant, but maximizes setContrast() range

//U8G2_SSD1306_128X64_ALT0_F_4W_HW_SPI u8g2(U8G2_R0, /* cs=*/ 10, /* dc=*/ 9, /* reset=*/ 8);    // same as the NONAME variant, but may solve the "every 2nd line skipped" problem

//U8G2_SH1106_128X64_NONAME_F_4W_HW_SPI u8g2(U8G2_R0, /* cs=*/ 10, /* dc=*/ 9, /* reset=*/ 8);

//U8G2_SH1106_128X64_NONAME_F_HW_I2C u8g2(U8G2_R0, /* reset=*/ U8X8_PIN_NONE);

//U8G2_SH1106_128X64_VCOMH0_F_4W_HW_SPI u8g2(U8G2_R0, /* cs=*/ 10, /* dc=*/ 9, /* reset=*/ 8);        // same as the NONAME variant, but maximizes setContrast() range

//U8G2_SH1106_128X64_WINSTAR_F_4W_HW_SPI u8g2(U8G2_R0, /* cs=*/ 10, /* dc=*/ 9, /* reset=*/ 8);        // same as the NONAME variant, but uses updated SH1106 init sequence

//U8G2_SH1107_64X128_F_4W_HW_SPI u8g2(U8G2_R0, /* cs=*/ 10, /* dc=*/ 9, /* reset=*/ 8);

//U8G2_SH1107_128X128_F_4W_HW_SPI u8g2(U8G2_R0, /* cs=*/ 10, /* dc=*/ 9, /* reset=*/ 8);

//U8G2_SH1107_128X128_F_HW_I2C u8g2(U8G2_R0, /* reset=*/ 8);

//U8G2_SH1107_SEEED_96X96_F_4W_HW_SPI u8g2(U8G2_R0, /* cs=*/ 10, /* dc=*/ 9, /* reset=*/ 8);

//U8G2_SSD1306_128X32_UNIVISION_F_SW_I2C u8g2(U8G2_R0, /* clock=*/ 21, /* data=*/ 20, /* reset=*/ U8X8_PIN_NONE);   // Adafruit Feather M0 Basic Proto + FeatherWing OLED

//U8G2_SSD1306_128X32_UNIVISION_F_SW_I2C u8g2(U8G2_R0, /* clock=*/ SCL, /* data=*/ SDA, /* reset=*/ U8X8_PIN_NONE);   // Adafruit Feather ESP8266/32u4 Boards + FeatherWing OLED

//U8G2_SSD1306_128X32_UNIVISION_F_HW_I2C u8g2(U8G2_R0, /* reset=*/ U8X8_PIN_NONE);  // Adafruit ESP8266/32u4/ARM Boards + FeatherWing OLED

//U8G2_SSD1306_128X32_UNIVISION_F_HW_I2C u8g2(U8G2_R0, /* reset=*/ U8X8_PIN_NONE, /* clock=*/ SCL, /* data=*/ SDA);   // pin remapping with ESP8266 HW I2C

//U8G2_SSD1306_64X48_ER_F_HW_I2C u8g2(U8G2_R0, /* reset=*/ U8X8_PIN_NONE);   // EastRising 0.66" OLED breakout board, Uno: A4=SDA, A5=SCL, 5V powered

//U8G2_SSD1306_64X32_NONAME_F_HW_I2C u8g2(U8G2_R0, /* reset=*/ U8X8_PIN_NONE);

//U8G2_SSD1306_64X32_1F_F_HW_I2C u8g2(U8G2_R0, /* reset=*/ U8X8_PIN_NONE);

//U8G2_SSD1306_96X16_ER_F_HW_I2C u8g2(U8G2_R0, /* reset=*/ U8X8_PIN_NONE);   // EastRising 0.69" OLED

//U8G2_SSD1322_NHD_256X64_F_4W_SW_SPI u8g2(U8G2_R0, /* clock=*/ 13, /* data=*/ 11, /* cs=*/ 10, /* dc=*/ 9, /* reset=*/ 8);    // Enable U8G2_16BIT in u8g2.h

//U8G2_SSD1322_NHD_256X64_F_4W_HW_SPI u8g2(U8G2_R0, /* cs=*/ 10, /* dc=*/ 9, /* reset=*/ 8);    // Enable U8G2_16BIT in u8g2.h

//U8G2_SSD1322_NHD_128X64_F_4W_SW_SPI u8g2(U8G2_R0, /* clock=*/ 13, /* data=*/ 11, /* cs=*/ 10, /* dc=*/ 9, /* reset=*/ 8);

//U8G2_SSD1322_NHD_128X64_F_4W_HW_SPI u8g2(U8G2_R0, /* cs=*/ 10, /* dc=*/ 9, /* reset=*/ 8);

//U8G2_SSD1325_NHD_128X64_F_4W_SW_SPI u8g2(U8G2_R0, /* clock=*/ 13, /* data=*/ 11, /* cs=*/ 10, /* dc=*/ 9, /* reset=*/ 8);

//U8G2_SSD1325_NHD_128X64_F_4W_HW_SPI u8g2(U8G2_R0, /* cs=*/ 10, /* dc=*/ 9, /* reset=*/ 8);

//U8G2_SSD1326_ER_256X32_1_4W_SW_SPI u8g2(U8G2_R0, /* clock=*/ 13, /* data=*/ 11, /* cs=*/ 10, /* dc=*/ 9, /* reset=*/ 8);         // experimental driver for ER-OLED018-1

//U8G2_SSD1327_SEEED_96X96_F_SW_I2C u8g2(U8G2_R0, /* clock=*/ SCL, /* data=*/ SDA, /* reset=*/ U8X8_PIN_NONE);    // Seeedstudio Grove OLED 96x96

//U8G2_SSD1327_SEEED_96X96_F_HW_I2C u8g2(U8G2_R0, /* reset=*/ U8X8_PIN_NONE);    // Seeedstudio Grove OLED 96x96

//U8G2_SSD1327_MIDAS_128X128_F_4W_SW_SPI u8g2(U8G2_R0, /* clock=*/ 13, /* data=*/ 11, /* cs=*/ 10, /* dc=*/ 9, /* reset=*/ 8);

//U8G2_SSD1327_MIDAS_128X128_F_4W_HW_SPI u8g2(U8G2_R0, /* cs=*/ 10, /* dc=*/ 9, /* reset=*/ 8);

//U8G2_SSD1329_128X96_NONAME_F_4W_SW_SPI u8g2(U8G2_R0, /* clock=*/ 13, /* data=*/ 11, /* cs=*/ 10, /* dc=*/ 9, /* reset=*/ 8);

//U8G2_SSD1329_128X96_NONAME_F_4W_HW_SPI u8g2(U8G2_R0, /* cs=*/ 10, /* dc=*/ 9, /* reset=*/ 8);

//U8G2_SSD1305_128X32_NONAME_F_4W_SW_SPI u8g2(U8G2_R0, /* clock=*/ 13, /* data=*/ 11, /* cs=*/ 10, /* dc=*/ 9, /* reset=*/ 8);

//U8G2_SSD1305_128X32_NONAME_F_4W_HW_SPI u8g2(U8G2_R0, /* cs=*/ 10, /* dc=*/ 9, /* reset=*/ 8);

//U8G2_SSD1309_128X64_NONAME0_F_4W_SW_SPI u8g2(U8G2_R0, /* clock=*/ 13, /* data=*/ 11, /* cs=*/ 10, /* dc=*/ 9, /* reset=*/ 8);

//U8G2_SSD1309_128X64_NONAME0_F_4W_HW_SPI u8g2(U8G2_R0, /* cs=*/ 10, /* dc=*/ 9, /* reset=*/ 8);

//U8G2_SSD1309_128X64_NONAME2_F_4W_SW_SPI u8g2(U8G2_R0, /* clock=*/ 13, /* data=*/ 11, /* cs=*/ 10, /* dc=*/ 9, /* reset=*/ 8);

//U8G2_SSD1309_128X64_NONAME2_F_4W_HW_SPI u8g2(U8G2_R0, /* cs=*/ 10, /* dc=*/ 9, /* reset=*/ 8);

//U8G2_LD7032_60X32_F_4W_SW_SPI u8g2(U8G2_R0, /* clock=*/ 11, /* data=*/ 12, /* cs=*/ 9, /* dc=*/ 10, /* reset=*/ 8);    // SW SPI Nano Board

//U8G2_LD7032_60X32_F_4W_SW_I2C u8g2(U8G2_R0, /* clock=*/ 11, /* data=*/ 12, /* reset=*/ U8X8_PIN_NONE);    // NOT TESTED!

//U8G2_UC1701_EA_DOGS102_F_4W_SW_SPI u8g2(U8G2_R0, /* clock=*/ 13, /* data=*/ 11, /* cs=*/ 10, /* dc=*/ 9, /* reset=*/ 8);

//U8G2_UC1701_EA_DOGS102_F_4W_HW_SPI u8g2(U8G2_R0, /* cs=*/ 10, /* dc=*/ 9, /* reset=*/ 8);

//U8G2_PCD8544_84X48_F_4W_SW_SPI u8g2(U8G2_R0, /* clock=*/ 13, /* data=*/ 11, /* cs=*/ 10, /* dc=*/ 9, /* reset=*/ 8);  // Nokia 5110 Display

//U8G2_PCD8544_84X48_F_4W_HW_SPI u8g2(U8G2_R0, /* cs=*/ 10, /* dc=*/ 9, /* reset=*/ 8);         // Nokia 5110 Display

//U8G2_PCF8812_96X65_F_4W_SW_SPI u8g2(U8G2_R0, /* clock=*/ 13, /* data=*/ 11, /* cs=*/ 10, /* dc=*/ 9, /* reset=*/ 8);    // Could be also PCF8814

//U8G2_PCF8812_96X65_F_4W_HW_SPI u8g2(U8G2_R0, /* cs=*/ 10, /* dc=*/ 9, /* reset=*/ 8);                        // Could be also PCF8814

//U8G2_HX1230_96X68_F_3W_SW_SPI u8g2(U8G2_R0, /* clock=*/ 13, /* data=*/ 11, /* cs=*/ 10, /* reset=*/ 8);

//U8G2_HX1230_96X68_F_4W_SW_SPI u8g2(U8G2_R0, /* clock=*/ 13, /* data=*/ 11, /* cs=*/ 10, /* dc=*/ 9, /* reset=*/ 8);

//U8G2_KS0108_128X64_F u8g2(U8G2_R0, 8, 9, 10, 11, 4, 5, 6, 7, /*enable=*/ 18, /*dc=*/ 17, /*cs0=*/ 14, /*cs1=*/ 15, /*cs2=*/ U8X8_PIN_NONE, /* reset=*/  U8X8_PIN_NONE);     // Set R/W to low!

//U8G2_KS0108_ERM19264_F u8g2(U8G2_R0, 8, 9, 10, 11, 4, 5, 6, 7, /*enable=*/ 18, /*dc=*/ 17, /*cs0=*/ 14, /*cs1=*/ 15, /*cs2=*/ 16, /* reset=*/  U8X8_PIN_NONE);     // Set R/W to low!

//U8G2_ST7920_192X32_F_8080 u8g2(U8G2_R0, 8, 9, 10, 11, 4, 5, 6, 7, /*enable=*/ 18, /*cs=*/ U8X8_PIN_NONE, /*dc=*/ 17, /*reset=*/ U8X8_PIN_NONE);

//U8G2_ST7920_192X32_F_SW_SPI u8g2(U8G2_R0, /* clock=*/ 18 /* A4 */ , /* data=*/ 16 /* A2 */, /* CS=*/ 17 /* A3 */, /* reset=*/ U8X8_PIN_NONE);

//U8G2_ST7920_128X64_F_8080 u8g2(U8G2_R0, 8, 9, 10, 11, 4, 5, 6, 7, /*enable=*/ 18 /* A4 */, /*cs=*/ U8X8_PIN_NONE, /*dc/rs=*/ 17 /* A3 */, /*reset=*/ 15 /* A1 */);    // Remember to set R/W to 0

//U8G2_ST7920_128X64_F_SW_SPI u8g2(U8G2_R0, /* clock=*/ 18 /* A4 */ , /* data=*/ 16 /* A2 */, /* CS=*/ 17 /* A3 */, /* reset=*/ U8X8_PIN_NONE);

//U8G2_ST7920_128X64_F_SW_SPI u8g2(U8G2_R0, /* clock=*/ 13, /* data=*/ 11, /* CS=*/ 10, /* reset=*/ 8);

//U8G2_ST7920_128X64_F_HW_SPI u8g2(U8G2_R0, /* CS=*/ 10, /* reset=*/ 8);

//U8G2_ST7565_EA_DOGM128_F_4W_SW_SPI u8g2(U8G2_R0, /* clock=*/ 13, /* data=*/ 11, /* cs=*/ 10, /* dc=*/ 9, /* reset=*/ 8);

//U8G2_ST7565_EA_DOGM128_F_4W_HW_SPI u8g2(U8G2_R0, /* cs=*/ 10, /* dc=*/ 9, /* reset=*/ 8);

//U8G2_ST7565_64128N_F_4W_SW_SPI u8g2(U8G2_R0, /* clock=*/ 13, /* data=*/ 11, /* cs=*/ 10, /* dc=*/ 9, /* reset=*/ 8);

//U8G2_ST7565_64128N_F_4W_HW_SPI u8g2(U8G2_R0, /* cs=*/ 10, /* dc=*/ 9, /* reset=*/ 8);

//U8G2_ST7565_EA_DOGM132_F_4W_SW_SPI u8g2(U8G2_R0, /* clock=*/ 13, /* data=*/ 11, /* cs=*/ 10, /* dc=*/ 9, /* reset=*/ U8X8_PIN_NONE);    // DOGM132 Shield

//U8G2_ST7565_EA_DOGM132_F_4W_HW_SPI u8g2(U8G2_R0, /* cs=*/ 10, /* dc=*/ 9, /* reset=*/ U8X8_PIN_NONE);    // DOGM132 Shield

//U8G2_ST7565_ZOLEN_128X64_F_4W_SW_SPI u8g2(U8G2_R0, /* clock=*/ 13, /* data=*/ 11, /* cs=*/ 10, /* dc=*/ 9, /* reset=*/ 8);

//U8G2_ST7565_ZOLEN_128X64_F_4W_HW_SPI u8g2(U8G2_R0, /* cs=*/ 10, /* dc=*/ 9, /* reset=*/ 8);

//U8G2_ST7565_LM6059_F_4W_SW_SPI u8g2(U8G2_R0, /* clock=*/ 13, /* data=*/ 11, /* cs=*/ 10, /* dc=*/ 9, /* reset=*/ 8);        // Adafruit ST7565 GLCD

//U8G2_ST7565_LM6059_F_4W_HW_SPI u8g2(U8G2_R0, /* cs=*/ 10, /* dc=*/ 9, /* reset=*/ 8);        // Adafruit ST7565 GLCD

//U8G2_ST7565_ERC12864_F_4W_SW_SPI u8g2(U8G2_R0, /* clock=*/ 13, /* data=*/ 11, /* cs=*/ 10, /* dc=*/ 9, /* reset=*/ 8);

//U8G2_ST7565_ERC12864_F_4W_HW_SPI u8g2(U8G2_R0, /* cs=*/ 10, /* dc=*/ 9, /* reset=*/ 8);

//U8G2_ST7565_NHD_C12832_F_4W_SW_SPI u8g2(U8G2_R0, /* clock=*/ 13, /* data=*/ 11, /* cs=*/ 10, /* dc=*/ 9, /* reset=*/ 8);

//U8G2_ST7565_NHD_C12832_F_4W_HW_SPI u8g2(U8G2_R0, /* cs=*/ 10, /* dc=*/ 9, /* reset=*/ 8);

//U8G2_ST7565_NHD_C12864_F_4W_SW_SPI u8g2(U8G2_R0, /* clock=*/ 13, /* data=*/ 11, /* cs=*/ 10, /* dc=*/ 9, /* reset=*/ 8);

//U8G2_ST7565_NHD_C12864_F_4W_HW_SPI u8g2(U8G2_R0, /* cs=*/ 10, /* dc=*/ 9, /* reset=*/ 8);

//U8G2_ST7567_PI_132X64_F_4W_SW_SPI u8g2(U8G2_R0, /* clock=*/ 13, /* data=*/ 11, /* cs=*/ 7, /* dc=*/ 9, /* reset=*/ 8);  // Pax Instruments Shield, LCD_BL=6

//U8G2_ST7567_PI_132X64_F_4W_HW_SPI u8g2(U8G2_R0, /* cs=*/ 7, /* dc=*/ 9, /* reset=*/ 8);  // Pax Instruments Shield, LCD_BL=6

//U8G2_ST7567_JLX12864_F_4W_SW_SPI u8g2(U8G2_R0, /* clock=*/ 13, /* data=*/ 11, /* cs=*/ 7, /* dc=*/ 9, /* reset=*/ 8);

//U8G2_ST7567_JLX12864_F_4W_HW_SPI u8g2(U8G2_R0, /* cs=*/ 7, /* dc=*/ 9, /* reset=*/ 8);

//U8G2_ST75256_JLX172104_F_4W_SW_SPI u8g2(U8G2_R0, /* clock=*/ 13, /* data=*/ 11, /* cs=*/ 10, /* dc=*/ 9, /* reset=*/ 8);

//U8G2_ST75256_JLX172104_F_4W_HW_SPI u8g2(U8G2_R0, /* cs=*/ 10, /* dc=*/ 9, /* reset=*/ 8);

//U8G2_ST75256_JLX256128_F_4W_SW_SPI u8g2(U8G2_R0, /* clock=*/ 13, /* data=*/ 11, /* cs=*/ 10, /* dc=*/ 9, /* reset=*/ 8);    // Enable U8g2 16 bit mode for this display

//U8G2_ST75256_JLX256128_F_4W_HW_SPI u8g2(U8G2_R0, /* cs=*/ 10, /* dc=*/ 9, /* reset=*/ 8);        // Enable U8g2 16 bit mode for this display

//U8G2_ST75256_JLX25664_F_2ND_HW_I2C u8g2(U8G2_R0, /* reset=*/ 8);    // Due, 2nd I2C, enable U8g2 16 bit mode for this display

//U8G2_NT7534_TG12864R_F_4W_SW_SPI u8g2(U8G2_R0, /* clock=*/ 13, /* data=*/ 11, /* cs=*/ 10, /* dc=*/ 9, /* reset=*/ 8);

//U8G2_NT7534_TG12864R_F_4W_HW_SPI u8g2(U8G2_R0, /* cs=*/ 10, /* dc=*/ 9, /* reset=*/ 8);

//U8G2_ST7588_JLX12864_F_SW_I2C u8g2(U8G2_R0, /* clock=*/ SCL, /* data=*/ SDA, /* reset=*/ 5);

//U8G2_ST7588_JLX12864_F_HW_I2C u8g2(U8G2_R0, /* reset=*/ 5);

//U8G2_IST3020_ERC19264_F_6800 u8g2(U8G2_R0, 44, 43, 42, 41, 40, 39, 38, 37,  /*enable=*/ 28, /*cs=*/ 32, /*dc=*/ 30, /*reset=*/ 31); // Connect WR pin with GND

//U8G2_IST3020_ERC19264_F_8080 u8g2(U8G2_R0, 44, 43, 42, 41, 40, 39, 38, 37,  /*enable=*/ 29, /*cs=*/ 32, /*dc=*/ 30, /*reset=*/ 31); // Connect RD pin with 3.3V

//U8G2_IST3020_ERC19264_F_4W_SW_SPI u8g2(U8G2_R0, /* clock=*/ 13, /* data=*/ 11, /* cs=*/ 10, /* dc=*/ 9, /* reset=*/ 8);

//U8G2_LC7981_160X80_F_6800 u8g2(U8G2_R0, 8, 9, 10, 11, 4, 5, 6, 7, /*enable=*/ 18, /*cs=*/ 14, /*dc=*/ 15, /*reset=*/ 16); // Connect RW with GND

//U8G2_LC7981_160X160_F_6800 u8g2(U8G2_R0, 8, 9, 10, 11, 4, 5, 6, 7, /*enable=*/ 18, /*cs=*/ 14, /*dc=*/ 15, /*reset=*/ 16); // Connect RW with GND

//U8G2_LC7981_240X128_F_6800 u8g2(U8G2_R0, 8, 9, 10, 11, 4, 5, 6, 7, /*enable=*/ 18, /*cs=*/ 14, /*dc=*/ 15, /*reset=*/ 16); // Connect RW with GND

//U8G2_SED1520_122X32_F u8g2(U8G2_R0, 8, 9, 10, 11, 4, 5, 6, 7, /*dc=*/ A0, /*e1=*/ A3, /*e2=*/ A2, /* reset=*/  A4);     // Set R/W to low!

//U8G2_T6963_240X128_F_8080 u8g2(U8G2_R0, 8, 9, 10, 11, 4, 5, 6, 7, /*enable=*/ 17, /*cs=*/ 14, /*dc=*/ 15, /*reset=*/ 16); // Connect RD with +5V, FS0 and FS1 with GND

//U8G2_T6963_256X64_F_8080 u8g2(U8G2_R0, 8, 9, 10, 11, 4, 5, 6, 7, /*enable=*/ 17, /*cs=*/ 14, /*dc=*/ 15, /*reset=*/ 16); // Connect RD with +5V, FS0 and FS1 with GND

//U8G2_SED1330_240X128_F_8080 u8g2(U8G2_R0, 8, 9, 10, 11, 4, 5, 6, 7, /*enable=*/ 17, /*cs=*/ 14, /*dc=*/ 15, /*reset=*/ 16); // Connect RD with +5V, FG with GND

//U8G2_SED1330_240X128_F_6800 u8g2(U8G2_R0, 13, 11, 2, 3, 4, 5, 6, A4, /*enable=*/ 7, /*cs=*/ 10, /*dc=*/ 9, /*reset=*/ 8); // A0 is dc pin!

//U8G2_RA8835_NHD_240X128_F_8080 u8g2(U8G2_R0, 8, 9, 10, 11, 4, 5, 6, 7, /*enable=*/ 17, /*cs=*/ 14, /*dc=*/ 15, /*reset=*/ 16); // Connect /RD = E with +5V, enable is /WR = RW, FG with GND, 14=Uno Pin A0

//U8G2_RA8835_NHD_240X128_F_6800 u8g2(U8G2_R0, 8, 9, 10, 11, 4, 5, 6, 7,  /*enable=*/ 17, /*cs=*/ 14, /*dc=*/ 15, /*reset=*/ 16); // A0 is dc pin, /WR = RW = GND, enable is /RD = E

//U8G2_UC1604_JLX19264_F_4W_SW_SPI u8g2(U8G2_R0, /* clock=*/ 13, /* data=*/ 11, /* cs=*/ 10, /* dc=*/ 9, /* reset=*/ 8);

//U8G2_UC1604_JLX19264_F_4W_HW_SPI u8g2(U8G2_R0, /* cs=*/ 10, /* dc=*/ 9, /* reset=*/ 8);

//U8G2_UC1608_ERC24064_F_4W_SW_SPI u8g2(U8G2_R0, /* clock=*/ 13, /* data=*/ 11, /* cs=*/ 10, /* dc=*/ 9, /* reset=*/ 8);  // SW SPI, Due ERC24064-1 Test Setup

//U8G2_UC1608_ERC240120_F_4W_SW_SPI u8g2(U8G2_R0, /* clock=*/ 13, /* data=*/ 11, /* cs=*/ 10, /* dc=*/ 9, /* reset=*/ 8);

//U8G2_UC1608_240X128_F_4W_SW_SPI u8g2(U8G2_R0, /* clock=*/ 13, /* data=*/ 11, /* cs=*/ 10, /* dc=*/ 9, /* reset=*/ 8);  // SW SPI, Due ERC24064-1 Test Setup

//U8G2_UC1610_EA_DOGXL160_F_4W_SW_SPI u8g2(U8G2_R0, /* clock=*/ 13, /* data=*/ 11, /* cs=*/ 10, /* dc=*/ 9, /* reset=*/  U8X8_PIN_NONE);

//U8G2_UC1610_EA_DOGXL160_F_4W_HW_SPI u8g2(U8G2_R0, /* cs=*/ 10, /* dc=*/ 9, /* reset=*/  U8X8_PIN_NONE);

//U8G2_UC1611_EA_DOGM240_F_2ND_HW_I2C u8g2(U8G2_R0, /* reset=*/ 8);    // Due, 2nd I2C, DOGM240 Test Board

//U8G2_UC1611_EA_DOGM240_F_4W_SW_SPI u8g2(U8G2_R0, /* clock=*/ 13, /* data=*/ 11, /* cs=*/ 10, /* dc=*/ 9, /* reset=*/ 8);   // Due, SW SPI, DOGXL240 Test Board

//U8G2_UC1611_EA_DOGXL240_F_2ND_HW_I2C u8g2(U8G2_R0, /* reset=*/ 8);    // Due, 2nd I2C, DOGXL240 Test Board

//U8G2_UC1611_EA_DOGXL240_F_4W_SW_SPI u8g2(U8G2_R0, /* clock=*/ 13, /* data=*/ 11, /* cs=*/ 10, /* dc=*/ 9, /* reset=*/ 8);   // Due, SW SPI, DOGXL240 Test Board

//U8G2_UC1611_EW50850_F_8080 u8g2(U8G2_R0, 8, 9, 10, 11, 4, 5, 6, 7,  /*enable=*/ 18, /*cs=*/ 3, /*dc=*/ 16, /*reset=*/ 16); // 240x160, Connect RD/WR1 pin with 3.3V, CS is aktive high

//U8G2_UC1638_160X128_F_4W_HW_SPI u8g2(U8G2_R2, /* cs=*/ 2, /* dc=*/ 3, /* reset=*/ 4);      // Not tested

//U8G2_SSD1606_172X72_F_4W_SW_SPI u8g2(U8G2_R0, /* clock=*/ 13, /* data=*/ 11, /* cs=*/ 10, /* dc=*/ 9, /* reset=*/ 8);        // eInk/ePaper Display

//U8G2_SSD1607_200X200_F_4W_SW_SPI u8g2(U8G2_R0, /* clock=*/ 13, /* data=*/ 11, /* cs=*/ 10, /* dc=*/ 9, /* reset=*/ 8);    // eInk/ePaper Display, original LUT from embedded artists

//U8G2_SSD1607_GD_200X200_F_4W_SW_SPI u8g2(U8G2_R0, /* clock=*/ 13, /* data=*/ 11, /* cs=*/ 10, /* dc=*/ 9, /* reset=*/ 8);    // Good Display

//U8G2_IL3820_296X128_F_4W_SW_SPI u8g2(U8G2_R0, /* clock=*/ 13, /* data=*/ 11, /* cs=*/ 10, /* dc=*/ 9, /* reset=*/ 8);    // WaveShare 2.9 inch eInk/ePaper Display, enable 16 bit mode for this display!

//U8G2_IL3820_V2_296X128_F_4W_SW_SPI u8g2(U8G2_R0, /* clock=*/ 13, /* data=*/ 11, /* cs=*/ 10, /* dc=*/ 9, /* reset=*/ 8);    // ePaper Display, lesser flickering and faster speed, enable 16 bit mode for this display!

// End of constructor list

void setup(void) {

  u8g2.begin();

  u8g2.enableUTF8Print();        // enable UTF8 support for the Arduino print() function

}

void loop(void) {

  u8g2.setFont(u8g2_font_unifont_t_chinese2);  // use chinese2 for all the glyphs of "你好世界"

  u8g2.setFontDirection();

  u8g2.clearBuffer();

  u8g2.setCursor(, );

  u8g2.print("Hello World!");

  u8g2.setCursor(, );

  u8g2.print("你好世界");        // Chinese "Hello World"

  u8g2.sendBuffer();

  delay();

}

Arduino通过I2C(SSD1306)驱动0.96寸12864OLED的更多相关文章

基于I2C总线的0.96寸OLED显示屏驱动
资料未整理,先占位置,以后补充
灵感手环第一步——0.96寸OLED显示实验
这算是我这个系列的第一篇博客吧.首先要解决的就是屏幕显示问题.我选择了目前新兴起的OLED显示模块. OLED(OrganicLightEmittingDiode),中文译作有机发光二极管,目前被广泛 ...
Arduino通过I2C(PCF8574T)驱动1602LCD
Arduino中使用I2C通信可直接调用Wire.h库, 这个库允许Arduino链接其他I2C设备, 链接线有两条, 分别是SDA(数据行)和SCI(时钟线). 各型号Arduino的I2C对应引脚 ...
Arduino SPI驱动7引脚0.96寸OLED SSD1306 调试笔记
https://www.geek-workshop.com/thread-37818-1-1.html 2.下载最新库https://learn.adafruit.com/monoc ... ibra ...
0.96寸OLED显示屏驱动手册（SSD1306）
MCU IIC接口 IIC通信接口由从地址位SA0,IIC总线数据信号SDA(输出SDAout/D2和输入SDAin /D1)和IIC总线时钟信号SCL(D0).不管是数据线还是时钟线都需要连接上拉电 ...
张高兴的 Windows 10 IoT 开发笔记：0.96 寸 I2C OLED
This is a Windows 10 IoT Core project on the Raspberry Pi 2/3, coded by C#. GitHub:https://github.co ...
SSD1306驱动的OLED实验
[转]http://bbs.21ic.com/icview-434543-1-1.html 前面几章的实例,均没涉及到液晶显示,这一章,我们将向大家介绍OLED的使用.在本章中,我们将使用战舰STM3 ...
i2c总线驱动，总线设备（适配器），从设备，从设备驱动的注册以及匹配
常用链接我的随笔我的评论我的参与最新评论我的标签随笔分类 ARM裸机(13) C(8) C++(8) GNU-ARM汇编 Linux驱动(24) Linux应用编程(5) Makefile ...
Linux I2C设备驱动编写（三）-实例分析AM3359
TI-AM3359 I2C适配器实例分析 I2C Spec简述特性: 兼容飞利浦I2C 2.1版本规格支持标准模式(100K bits/s)和快速模式(400K bits/s) 多路接收.发送模式 ...

随机推荐

【经验】STL的list vector在iterator迭代器的循环中使用erase 造成的BUG
#include <iostream> #include <list> #include <vector> using namespace std; typedef ...
go语言之进阶篇字符串操作常用函数介绍
下面这些函数来自于strings包,这里介绍一些我平常经常用到的函数,更详细的请参考官方的文档. 一.字符串操作常用函数介绍 1.Contains func Contains(s, substr st ...
Openfire XMPP Smack RTC IM 即时通讯聊天 MD
Markdown版本笔记我的GitHub首页我的博客我的微信我的邮箱 MyAndroidBlogs baiqiantao baiqiantao bqt20094 baiqiantao@sina ...
Java方法containsAll学习
有时候我们需要判断B链表是不是A链表的子集,我们可以使用A.containsAll(B)来判断,当返回值是true的时候就表明B链表是A链表的子集,当返回值是false时候就表明B链表不是A链表的子集 ...
Gridview 单选效果实现，且用且珍惜
Gridview 单选效果,在androidapp中实现非常频繁,我这里提供我的一种思路,这是我的思维导图: 怎么样将这样的思维导图翻译成java代码了,请看下面的代码了: // 电子产品的图片列表信 ...
Base64原理与实现
Base64编码说明 Base64编码要求把3个8位字节(3*8=24)转化为4个6位的字节(4*6=24),之后在6位的前面补两个0,形成8位一个字节的形式. 如果剩下的字符不足3个字节,则用0填充 ...
【Scala】Scala-调用Java-集合
Scala-调用Java-集合 sacla 遍历 java list_百度搜索 13.11 Scala混用Java的集合类调用scala的foreach遍历问题 - 简书
SQL 连接操作及查询分析
linux命令大全网站
一. linux命令大全网站 http://man.linuxde.net/watch
（NGUI）UISprite 切换图集
UISprite是可以使用代码动态切换图集的 using UnityEngine; using System.Collections; public class SpriteAtlasTest : M ...

Arduino通过I2C(SSD1306)驱动0.96寸12864OLED

Arduino通过I2C(SSD1306)驱动0.96寸12864OLED的更多相关文章

随机推荐

热门专题