每天一个linux命令(46):ping命令
Linux系统的ping 命令是常用的网络命令,它通常用来测试与目标主机的连通性,我们经常会说“ping一下某机器,看是不是开着”、不能打开网页时会说“你先ping网关地 址192.168.1.1试试”。它通过发送ICMP ECHO_REQUEST数据包到网络主机 (send ICMP ECHO_REQUEST to network hosts),并显示响应情况,这样我们就可以根据它输出的信息来确定目标主机 是否可访问(但这不是绝对的)。有些服务器为了防止通过ping探测到,通过防火墙设置了禁止ping或者在内核参数中禁止ping,这样就不能通过 ping确定该主机是否还处于开启状态。
linux下的ping和windows下的ping稍有区别,linux下ping不会自动终止,需要按ctrl+c终止或者用参数-c指定要求完成的回应次数。
1.命令格式:
ping [参数] [主机名或IP地址]
2.命令功能:
ping命令用于:确定网络和各外部主机的状态;跟踪和隔离硬件和软件问题;测 试、评估和管理网络。如果主机正在运行并连在网上,它就对回送信号进行响应。每个回送信号请求包含一个网际协议(IP)和 ICMP 头,后面紧跟一 个 tim 结构,以及来填写这个信息包的足够的字节。缺省情况是连续发送回送信号请求直到接收到中断信号(Ctrl-C)。
ping 命 令每秒发送一个数据报并且为每个接收到的响应打印一行输出。ping 命令计算信号往返时间和(信息)包丢失情况的统计信息,并且在完成之后显示一个简要 总结。ping 命令在程序超时或当接收到 SIGINT 信号时结束。Host 参数或者是一个有效的主机名或者是因特网地址。
3.命令参数:
-d 使用Socket的SO_DEBUG功能。
-f 极限检测。大量且快速地送网络封包给一台机器,看它的回应。
-n 只输出数值。
-q 不显示任何传送封包的信息,只显示最后的结果。
-r 忽略普通的Routing Table,直接将数据包送到远端主机上。通常是查看本机的网络接口是否有问题。
-R 记录路由过程。
-v 详细显示指令的执行过程。
<p>-c 数目:在发送指定数目的包后停止。
-i 秒数:设定间隔几秒送一个网络封包给一台机器,预设值是一秒送一次。
-I 网络界面:使用指定的网络界面送出数据包。
-l 前置载入:设置在送出要求信息之前,先行发出的数据包。
-p 范本样式:设置填满数据包的范本样式。
-s 字节数:指定发送的数据字节数,预设值是56,加上8字节的ICMP头,一共是64ICMP数据字节。
-t 存活数值:设置存活数值TTL的大小。
4.使用实例:
实例1:ping的通的情况
命令:
ping 192.168.120.205
输出:
[root@localhost ~]# ping 192.168.120.205
PING 192.168.120.205 (192.168.120.205) 56(84) bytes of data.
64 bytes from 192.168.120.205: icmp_seq=1 ttl=64 time=0.720 ms
64 bytes from 192.168.120.205: icmp_seq=2 ttl=64 time=0.181 ms
64 bytes from 192.168.120.205: icmp_seq=3 ttl=64 time=0.191 ms
64 bytes from 192.168.120.205: icmp_seq=4 ttl=64 time=0.188 ms
64 bytes from 192.168.120.205: icmp_seq=5 ttl=64 time=0.189 ms --- 192.168.120.205 ping statistics ---
5 packets transmitted, 5 received, 0% packet loss, time 4000ms
rtt min/avg/max/mdev = 0.181/0.293/0.720/0.214 ms
[root@localhost ~]#
说明:
实例2:ping不通的情况
命令:
ping 192.168.120.202
输出:
[root@localhost ~]# ping 192.168.120.202
PING 192.168.120.202 (192.168.120.202) 56(84) bytes of data.
From 192.168.120.204 icmp_seq=1 Destination Host Unreachable
From 192.168.120.204 icmp_seq=2 Destination Host Unreachable
From 192.168.120.204 icmp_seq=3 Destination Host Unreachable
From 192.168.120.204 icmp_seq=4 Destination Host Unreachable
From 192.168.120.204 icmp_seq=5 Destination Host Unreachable
From 192.168.120.204 icmp_seq=6 Destination Host Unreachable --- 192.168.120.202 ping statistics ---
8 packets transmitted, 0 received, +6 errors, 100% packet loss, time 7005ms
, pipe 4
[root@localhost ~]#
说明:
实例3:ping网关
命令:
ping -b 192.168.120.1
输出:
[root@localhost ~]# route
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
192.168.120.0 * 255.255.255.0 U 0 0 0 eth0
192.168.0.0 192.168.120.1 255.255.0.0 UG 0 0 0 eth0
10.0.0.0 192.168.120.1 255.0.0.0 UG 0 0 0 eth0
default 192.168.120.240 0.0.0.0 UG 0 0 0 eth0
[root@localhost ~]# ping -b 192.168.120.1
PING 192.168.120.1 (192.168.120.1) 56(84) bytes of data.
64 bytes from 192.168.120.1: icmp_seq=1 ttl=255 time=2.02 ms
64 bytes from 192.168.120.1: icmp_seq=2 ttl=255 time=1.83 ms
64 bytes from 192.168.120.1: icmp_seq=3 ttl=255 time=1.68 ms
64 bytes from 192.168.120.1: icmp_seq=4 ttl=255 time=1.98 ms
64 bytes from 192.168.120.1: icmp_seq=5 ttl=255 time=1.88 ms --- 192.168.120.1 ping statistics ---
5 packets transmitted, 5 received, 0% packet loss, time 4000ms
rtt min/avg/max/mdev = 1.682/1.880/2.020/0.129 ms
说明:
实例4:ping指定次数
命令:
ping -c 10 192.168.120.206
输出:
[root@localhost ~]# ping -c 10 192.168.120.206
PING 192.168.120.206 (192.168.120.206) 56(84) bytes of data.
64 bytes from 192.168.120.206: icmp_seq=1 ttl=64 time=1.25 ms
64 bytes from 192.168.120.206: icmp_seq=2 ttl=64 time=0.260 ms
64 bytes from 192.168.120.206: icmp_seq=3 ttl=64 time=0.242 ms
64 bytes from 192.168.120.206: icmp_seq=4 ttl=64 time=0.271 ms
64 bytes from 192.168.120.206: icmp_seq=5 ttl=64 time=0.274 ms
64 bytes from 192.168.120.206: icmp_seq=6 ttl=64 time=0.295 ms
64 bytes from 192.168.120.206: icmp_seq=7 ttl=64 time=0.269 ms
64 bytes from 192.168.120.206: icmp_seq=8 ttl=64 time=0.270 ms
64 bytes from 192.168.120.206: icmp_seq=9 ttl=64 time=0.253 ms
64 bytes from 192.168.120.206: icmp_seq=10 ttl=64 time=0.289 ms --- 192.168.120.206 ping statistics ---
10 packets transmitted, 10 received, 0% packet loss, time 9000ms
rtt min/avg/max/mdev = 0.242/0.367/1.251/0.295 ms
[root@localhost ~]#
说明:
实例5:时间间隔和次数限制的ping
命令:
ping -c 10 -i 0.5 192.168.120.206
输出:
[root@localhost ~]# ping -c 10 -i 0.5 192.168.120.206
PING 192.168.120.206 (192.168.120.206) 56(84) bytes of data.
64 bytes from 192.168.120.206: icmp_seq=1 ttl=64 time=1.24 ms
64 bytes from 192.168.120.206: icmp_seq=2 ttl=64 time=0.235 ms
64 bytes from 192.168.120.206: icmp_seq=3 ttl=64 time=0.244 ms
64 bytes from 192.168.120.206: icmp_seq=4 ttl=64 time=0.300 ms
64 bytes from 192.168.120.206: icmp_seq=5 ttl=64 time=0.255 ms
64 bytes from 192.168.120.206: icmp_seq=6 ttl=64 time=0.264 ms
64 bytes from 192.168.120.206: icmp_seq=7 ttl=64 time=0.263 ms
64 bytes from 192.168.120.206: icmp_seq=8 ttl=64 time=0.331 ms
64 bytes from 192.168.120.206: icmp_seq=9 ttl=64 time=0.247 ms
64 bytes from 192.168.120.206: icmp_seq=10 ttl=64 time=0.244 ms --- 192.168.120.206 ping statistics ---
10 packets transmitted, 10 received, 0% packet loss, time 4499ms
rtt min/avg/max/mdev = 0.235/0.362/1.241/0.294 ms
[root@localhost ~]# ping -c 10 -i 0.01 192.168.120.206
PING 192.168.120.206 (192.168.120.206) 56(84) bytes of data.
64 bytes from 192.168.120.206: icmp_seq=1 ttl=64 time=0.244 ms
64 bytes from 192.168.120.206: icmp_seq=2 ttl=64 time=0.195 ms
64 bytes from 192.168.120.206: icmp_seq=3 ttl=64 time=0.219 ms
64 bytes from 192.168.120.206: icmp_seq=4 ttl=64 time=0.204 ms
64 bytes from 192.168.120.206: icmp_seq=5 ttl=64 time=3.56 ms
64 bytes from 192.168.120.206: icmp_seq=6 ttl=64 time=1.93 ms
64 bytes from 192.168.120.206: icmp_seq=7 ttl=64 time=0.193 ms
64 bytes from 192.168.120.206: icmp_seq=8 ttl=64 time=0.193 ms
64 bytes from 192.168.120.206: icmp_seq=9 ttl=64 time=0.202 ms
64 bytes from 192.168.120.206: icmp_seq=10 ttl=64 time=0.211 ms --- 192.168.120.206 ping statistics ---
10 packets transmitted, 10 received, 0% packet loss, time 90ms
rtt min/avg/max/mdev = 0.193/0.716/3.564/1.080 ms
[root@localhost ~]#
说明:
实例6:通过域名ping公网上的站点
命令:
ping -c 5 www.58.com
输出:
peida-VirtualBox ~ # ping -c 5 www.58.com
PING www.58.com (211.151.111.30) 56(84) bytes of data.
64 bytes from 211.151.111.30: icmp_req=1 ttl=49 time=14.7 ms
64 bytes from 211.151.111.30: icmp_req=2 ttl=49 time=16.4 ms
64 bytes from 211.151.111.30: icmp_req=3 ttl=49 time=15.2 ms
64 bytes from 211.151.111.30: icmp_req=4 ttl=49 time=14.6 ms
64 bytes from 211.151.111.30: icmp_req=5 ttl=49 time=19.9 ms --- www.58.com ping statistics ---
5 packets transmitted, 5 received, 0% packet loss, time 20101ms
rtt min/avg/max/mdev = 14.618/16.192/19.917/1.965 ms
peida-VirtualBox ~ #
说明:
实例7:多参数使用
命令:
ping -i 3 -s 1024 -t 255 192.168.120.206
输出:
[root@localhost ~]# ping -i 3 -s 1024 -t 255 192.168.120.206
PING 192.168.120.206 (192.168.120.206) 1024(1052) bytes of data.
1032 bytes from 192.168.120.206: icmp_seq=1 ttl=64 time=1.99 ms
1032 bytes from 192.168.120.206: icmp_seq=2 ttl=64 time=0.694 ms
1032 bytes from 192.168.120.206: icmp_seq=3 ttl=64 time=0.300 ms
1032 bytes from 192.168.120.206: icmp_seq=4 ttl=64 time=0.481 ms
1032 bytes from 192.168.120.206: icmp_seq=5 ttl=64 time=0.415 ms
1032 bytes from 192.168.120.206: icmp_seq=6 ttl=64 time=0.600 ms
1032 bytes from 192.168.120.206: icmp_seq=7 ttl=64 time=0.411 ms
1032 bytes from 192.168.120.206: icmp_seq=8 ttl=64 time=0.281 ms
1032 bytes from 192.168.120.206: icmp_seq=9 ttl=64 time=0.318 ms
1032 bytes from 192.168.120.206: icmp_seq=10 ttl=64 time=0.362 ms
1032 bytes from 192.168.120.206: icmp_seq=11 ttl=64 time=0.408 ms
1032 bytes from 192.168.120.206: icmp_seq=12 ttl=64 time=0.445 ms
1032 bytes from 192.168.120.206: icmp_seq=13 ttl=64 time=0.397 ms
1032 bytes from 192.168.120.206: icmp_seq=14 ttl=64 time=0.406 ms
1032 bytes from 192.168.120.206: icmp_seq=15 ttl=64 time=0.458 ms --- 192.168.120.206 ping statistics ---
15 packets transmitted, 15 received, 0% packet loss, time 41999ms
rtt min/avg/max/mdev = 0.281/0.531/1.993/0.404 ms
[root@localhost ~]#
说明:
-i 3 发送周期为 3秒 -s 设置发送包的大小为1024 -t 设置TTL值为 255
每天一个linux命令(46):ping命令的更多相关文章
- 每天一个linux命令(41)--ping命令
Linux系统的 ping 命令是常用的网络命令,它通常用来测试与目标主机的连通性,它通过发送 ICMP ECHO_REQUEST数据包到网络主机(send ICMP ECHO_REQUEST t ...
- linux常用命令:ping 命令
Linux系统的ping 命令是常用的网络命令,它通常用来测试与目标主机的连通性,我们经常会说“ping一下某机器,看是不是开着”.不能打开网页时会说“你先ping网关地 址192.168.1.1试试 ...
- 网工最实用最常用的网络命令之一——Ping 命令详解(一)
Ping是Windows.Unix和Linux系统下的一个命令.ping也属于一个通信协议,是TCP/IP协议的一部分.利用“ping”命令可以检查网络是否连通,可以很好地帮助我们分析和判定网络故障. ...
- windows 环境和linux环境下 ping命令的区别:
Ping 是Windows自带的一个DOS命令.利用它可以检查网络是否能够连通,用好它可以很好地帮助我们分析判定网络故障.该命令可以加许多参数使用,键入Ping按回车即可看到详细说明.Ping 命令可 ...
- Linux系统下ping命令报错 name or service not know
问题描述 CentOS,但是当执行ping命令的时候,提示name or service not known 解决方法 1.添加DNS服务器 vi /etc/resolv.conf 进入编辑模式,增加 ...
- linux下安装 ping 命令
使用docker仓库下载的ubuntu 14.04 镜像.里面精简的连 ping 命令都没有.google 百度都搜索不到ping 命令在哪个包里. 努力找了半天,在一篇文章的字里行间发现了 ping ...
- Linux命令:ping命令
ping命令:类似于windows的ping命令,用于测试网络主机ICMP请求回应的 ping选项 ping -c # # 执行次数 -w # #测试 ...
- 常见网络命令之Ping命令
前言:计算机网络老师要求我们自己总结一下常见的网络命,然后上课可以上去讲一下这些命令使用,像我这么听话的好学生,肯定是照老师要求,认真的总结了一下,总结的过程中,我发现网上已经有的资源讲的都不是很详细 ...
- ping命令知识 Ping命令工作原理详解
在网络应用中,ping网速与IP地址等都是非常常用的命令,但大家知道ping命令的工作原理吗?要知道这其中的奥秘,我们有必要来看看Ping命令的工作过程到底是怎么样的.下面介绍下ping命令的详细知识 ...
- ssh命令、ping命令、traceroute 命令所使用的协议
在Node reboot or eviction: How to check if yourprivate interconnect CRS can transmit network heartbea ...
随机推荐
- Hive UDF 实验1
项目中使用的hive版本低于0.11,无法使用hive在0.11中新加的开窗分析函数. 在项目中需要使用到row_number()函数的地方,有人写了udf来实现这个功能. new java proj ...
- git的使用(二)
1.几个概念 (1)工作区指当前编辑代码的地方,是.git仓库所在的文件夹. (2)暂存区是一个概念,并不存在这个区. (3)仓库是.git文件夹,是运行git init命令时自动创建的,默认是隐藏的 ...
- selenium如何分别启动IE、firefox、chrome浏览器
1.火狐浏览器 /* * 初始化火狐浏览器 * */ public static WebDriver initFireFox(WebDriver dr) { String key = "we ...
- Tarjian算法求强联通分量
如果两个顶点可以相互通达,则称两个顶点强连通(strongly connected).如果有向图G的每两个顶点都强连通,称G是一个强连通图.强连通图有向图的极大强连通子图,称为强连通分量(strong ...
- JavaScript Promise API
同步编程通常来说易于调试和维护,然而,异步编程通常能获得更好的性能和更大的灵活性.异步的最大特点是无需等待."Promises"渐渐成为JavaScript里最重要的一部分,大量的 ...
- 关于jQuery的一些实用代码
(1)修改默认编码:(将默认的utf-8,修改为GB2312) $.ajaxSetup({ ajaxSettings:{contentType:"application/x-www-from ...
- .Net core Linux环境安装
10月份的时候在自己电脑上搭了开发环境,当时跑完Welcome后就搁置了一段时间,最近有一个小项目要正式采用core来开发并部署在linux环境下,于是在Linux上也搭建一个运行环境. 虽然不经常使 ...
- Maven 其他功能
测试:指定测试哪些测试类,指定哪些测试类不测试,可以使用通配符 使用 Hudson 进行持续集成 持续集成:快速且高频率地自动构建项目的所有源码,并为项目成员提供丰富的反馈信息 一个典型的持续集成场景 ...
- tee命令
tee命令 http://liubin.blog.51cto.com/282313/131298 https://en.wikipedia.org/wiki/Tee_(command)
- C++ c++初识
//c++初识 #include<iostream> //包含c++标准头文件 //<iostream>和<iostream.h>格式不一样,前者没有后缀,实际上, ...