linux网卡速率和双工模式的配置

(2012-09-06 14:39:57)

改变网络接口的速度和协商方式的工具miitool ethtool 通过mii-tool和ethtool工具来调整网卡的速度、双工等,这样能提高网卡的效率; mii-tool 配置网络设备协商方式的工具 mii-tool 介绍 mii-tool - view, manipulate media-independent interface status (mii-tool 是查看,管理介质的网络接口的状态) 有时网卡需要配置协商方式 ,比如10/100/1000M的网卡半双工、全双工、自动协商的配置。但大多数的网络设备是不用我们来修改协商,因为大多数网络设置接入的时候,都采用自动协商来解决相互通信的问题。但在有的情况下,需要我们手动来设置网卡的协商方式; mii-tool 就是能指定网卡的协商方式。 注明:我在使用mii-tool工具修改协商模式时,提示是错误的,因为是在虚拟机中做的,不过虚拟机中的网卡我查看是支持全双工模式的,可是提示错误SIOCGMIIPHY on ’eth0’ failed: Operation not supported,问题出在那里也不清楚,用google查了下,发现不少人都是这样的错误,也没说明原因;不过多数人提示可以使用ethtool工具去修改,我测试了下,还行!还有一种方法是修改/etc/modules.conf配置文件; #ethtool -s eth0 autoneg off #ethtool -s eth0 duplex full 在/etc/modules.conf添加内容 alias eth0 bcm5700 line_speed=100 full_duplex=1 options bcm5700 line_speed=100 full_duplex=1 重起! mii-tool 更改网络接口协商的方法; [root@localhost]# mii-tool --help usage: mii-tool [-VvRrwl] [-A media,... | -F media] [interface ...]     -V, --version display version information     -v, --verbose more verbose output 注:显示网络接口的信息;     -R, --reset reset MII to poweron state 注:重设MII到开启状态;     -r, --restart restart autonegotiation 注:重启自动协商模式;     -w, --watch monitor for link status changes 注:查看网络接口连接的状态变化;     -l, --log with -w, write events to syslog 注:写入事件到系统日志;     -A, --advertise=media,... advertise only specified media 注:指令特定的网络接口;   -F, --force=media force specified media technology 注:更改网络接口协商方式; media: 100baseT4, 100baseTx-FD, 100baseTx-HD, 10baseT-FD, 10baseT-HD,     (to advertise both HD and FD) 100baseTx, 10baseT
查看网络接口的协商状态 [root@localhost]# mii-tool -v eth0 eth0: negotiated 100baseTx-FD, link ok product info: vendor 00:00:00, model 0 rev 0 basic mode: autonegotiation enabled basic status: autonegotiation complete, link ok capabilities: 100baseTx-FD 100baseTx-HD 10baseT-FD 10baseT-HD advertising: 100baseTx-FD 100baseTx-HD 10baseT-FD 10baseT-HD link partner: 100baseTx-FD 100baseTx-HD 10baseT-FD 10baseT-HD flow-control 注:上面的例子,我们可以看得到是自动协商。注意红字的部份; 更改网络接口协商方式; 更改网络接口的协商方式,我们要用到-F选项,后面可以接 100baseT4, 100baseTx-FD, 100baseTx-HD, 10baseT-FD, 10baseT-HD等参数; 把网络接口eth0改为 1000Mb/s全双工的模式 [root@localhost]# mii-tool -F 100baseTx-FD
[root@localhost]#mii-tool -v eth0 eth0: 100 Mbit, full duplex, link ok product info: vendor 00:00:00, model 0 rev 0 basic mode:   100 Mbit, full duplex basic status: link ok capabilities: 100baseTx-FD 100baseTx-HD 10baseT-FD 10baseT-HD advertising: 100baseTx-FD 100baseTx-HD 10baseT-FD 10baseT-HD 也可以使用ethtool工具修改: [root@localhost]# ethtool -s eth0 speed 100 duplex full ethtool 工具关于网络协商功能介绍 ethtool - Display or change ethernet card settings(ethtool 是用来显示和更改网卡设置的工具);这个工具比较复杂,功能也特别多; ethtool 显示网络端口设置功能 [root@localhost]# ethtool eth0 Settings for eth0:   Supported ports: [ TP MII ]   Supported link modes: 10baseT/Half 10baseT/Full                 100baseT/Half 100baseT/Full     Supports auto-negotiation: Yes     Advertised link modes: 10baseT/Half 10baseT/Full                 100baseT/Half 100baseT/Full   Advertised auto-negotiation: No 注:自动协商关闭     Speed: 100Mb/s 注:速度 100Mb     Duplex: Full 注:全双工   Port: MII   PHYAD: 32   Transceiver: internal   Auto-negotiation: off   Supports Wake-on: pumbg   Wake-on: d     Current message level: 0x00000007 (7)     Link detected: yes 注:eth0已经激活; ethtool 设置网卡的协商模式; ethtool -s DEVNAME \           [ speed 10|100|1000 ] \         [ duplex half|full ] \         [ port tp|aui|bnc|mii|fibre ] \         [ autoneg on|off ] \ 把网卡eth0 速度改为10Mb/s,采用半双工; [root@localhost]# ethtool -s eth1 speed 10 duplex half [root@localhost]# ethtool eth1 Settings for eth1:   Supported ports: [ TP MII ]   Supported link modes:   10baseT/Half 10baseT/Full                 100baseT/Half 100baseT/Full   Supports auto-negotiation: Yes   Advertised link modes: 10baseT/Half 10baseT/Full                 100baseT/Half 100baseT/Full   Advertised auto-negotiation: No   Speed: 10Mb/s 注:速度 10M/s   Duplex: Half 注:半双工   Port: MII     PHYAD: 32     Transceiver: internal   Auto-negotiation: off   Supports Wake-on: pumbg   Wake-on: d     Current message level: 0x00000007 (7)     Link detected: no 注:eth1没有激活; 把网卡eth0 速度改为100Mb/s,采用全双工; [root@localhost]# ethtool -s eth1 speed 100 duplex full [root@localhost]# ethtool eth1 Settings for eth1:     Supported ports: [ TP MII ]     Supported link modes:   10baseT/Half 10baseT/Full                 100baseT/Half 100baseT/Full   Supports auto-negotiation: Yes   Advertised link modes: 10baseT/Half 10baseT/Full                 100baseT/Half 100baseT/Full   Advertised auto-negotiation: No   Speed: 100Mb/s 注:速度 100M/s   Duplex: Full 注:全双工   Port: MII     PHYAD: 32     Transceiver: internal   Auto-negotiation: off   Supports Wake-on: pumbg   Wake-on: d     Current message level: 0x00000007 (7)     Link detected: no 注:eth1网卡没有激活;

linux网卡速率和双工模式的配置的更多相关文章

  1. Linux网卡设置为网桥模式

    Linux网卡设置为网桥模式 1.    添加网卡,并修改相关配置文件 1.1虚拟机添加网卡,并配置相关文件 如:eth2为新添加网卡 cd /etc/sysconfig/network-script ...

  2. Network基础(四):MAC地址表及邻居信息查看、配置接口速率及双工模式、配置交换机管理IP

    一.MAC地址表及邻居信息查看 目标: 本例要求为修改计算机名并加入工作组: 查看交换机MAC地址表 查看CISCO设备邻居信息 方案: 网络拓扑,如下图所示. 步骤: 步骤一:查看交换机sw1的ma ...

  3. (转)深度分析Linux下双网卡绑定七种模式

    现在一般的企业都会 使用双网卡接入,这样既能添加网络带宽,同时又能做相应的冗余,可以说是好处多多.而一般企业都会使用linux操作系统下自带的网卡绑定模式,当然现在 网卡产商也会出一些针对window ...

  4. 深度分析Linux下双网卡绑定七种模式

    现在一般的企业都会使用双网卡接入,这样既能添加网络带宽,同时又能做相应的冗余,可以说是好处多多.而一般企业都会使用linux操作系统下自带的网卡绑定模式,当然现在网卡产商也会出一些针对windows操 ...

  5. Linux 网卡 team配置

    网卡 team配置 目录 网卡 team配置 一.介绍 runner 方式: 1.roundrobin [mode 0]轮转策略 (balance-rr) 2.activebackup[mode 1] ...

  6. Linux网卡高级命令、IP别名及多网卡绑定 转

    http://www.cnblogs.com/xiaoluo501395377/archive/2013/05/26/3100065.html 本篇随笔将详细讲解Linux系统的网卡高级命令.IP别名 ...

  7. Linux网卡绑定探析

    2013-08-20 15:39:31 现在很多服务器都自带双千兆网口,利用网卡绑定既能增加网络带宽,同时又能做相应的冗余,目前应用于很多的场景.linux操作系统下自带的网卡绑定模式,Linux b ...

  8. 深度分析Linux下双网卡绑定七种模式 多网卡的7种bond模式原理

    http://blog.csdn.net/abc_ii/article/details/9991845多网卡的7种bond模式原理 Linux网卡绑定mode共有七种(~) bond0.bond1.b ...

  9. Linux下多网卡绑定bond0及模式

    Linux 多网卡绑定 网卡绑定mode共有七种(0~6) bond0.bond1.bond2.bond3.bond4.bond5.bond6 常用的有三种 mode=0:平衡负载模式,有自动备援,但 ...

随机推荐

  1. 10+ powerful debugging tricks with Visual Studio

    10+ powerful debugging tricks with Visual Studio Original link : http://www.codeproject.com/Articles ...

  2. App性能提升方法

    总体思路:精简请求数 1.css sprit 图像拼合,将所有可拼接的所有图像拼接为一整张图像,然后再利用css中的position定位来处理,降低图片的请求数 2.懒加载:只渲染客户端用户可见区域[ ...

  3. UIScrollView,UIPageControl

    #import <UIKit/UIKit.h> @interface ViewController : UIViewController<UIScrollViewDelegate&g ...

  4. WP开发笔记——日期时间DateTime.Now函数

    //2008年4月24日 System.DateTime.Now.ToString("D"); //2008-4-24 System.DateTime.Now.ToString(& ...

  5. Javascript this 解析

    Javascript中,this是一个非常有用的关键字, this是在运行时基于函数的运行环境绑定的,但是,如果使用的时候不注意,很容易就出错了. ECMAScript Standard对this的定 ...

  6. Jexus 高并发请求的优化技巧 笔记

    Jexus web server 5.1 每个工作进程的最大并发数固定为1万,最多可以同时开启4个工作进程,因此,每台Jexus V5.1服务器最多可以到支持4万个并发连接.但是,按照linux系统的 ...

  7. 微信小程序视频地址

    微信小程序视频系列教程完整版,课程中用到的源码附在帖子最后. [url=http://bbs.larkapp.com/forum.php?mod=viewthread&tid=5673][b] ...

  8. iOS 点击return或者点击屏幕键盘消失

    //定义两个文本框 UITextField *textName; UITextField *textSummary; //点击return 按钮 去掉 -(BOOL)textFieldShouldRe ...

  9. Oracle 动态视图4 V$SESSION_WAIT & V$SESSION_EVENT

    一.视图V$SESSION_WAIT显示了session的当前等待事 Column Datatype Description SID NUMBER Session identifier SEQ# NU ...

  10. 每日一“酷”之array

    array--国定类型数据序列 array模块定义一个序列数据结构,看起来和list非常相似,只不过所有成员都必须是相同的基本类型. 1.初始化 array实例化时可以提高一个参数来描述允许哪个种数据 ...