STM32 TIM3 PWM输出 4路

一、设置TIM3的GPIO为推挽输出

void TIM3_IOConfig(void)
{
        GPIO_InitTypeDef  GPIO_InitStructure;

        RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOA|RCC_APB2Periph_GPIOB,ENABLE);

        //这里TIM3的通道1是GPIOA_Pin_6,通道2是GPIOA_Pin_7;通道3是GPIOB_Pin_0；
        //这里TIM3的通道4是GPIOB_Pin_1;
        GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF_PP;
        //使用PWM的功能需要设置成AF_PP模式
        GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
        GPIO_InitStructure.GPIO_Pin = GPIO_Pin_6|GPIO_Pin_7;
        GPIO_Init(GPIOA,&GPIO_InitStructure);

        GPIO_InitStructure.GPIO_Pin = GPIO_Pin_0|GPIO_Pin_1;
        GPIO_Init(GPIOB,&GPIO_InitStructure);
}

二、设置TIM3的PWM1方式4路输出

//arr:自动重装值 psc:时钟预分频数
//定时器溢出时间计算：Tout=((arr+1)*(psc+1))/Ft
void TIM3_PWM_Init(void)
{
        TIM_TimeBaseInitTypeDef  TIM_TimeBaseInitStructure;//TIM定时器的配置
        TIM_OCInitTypeDef        TIM_OCInitStructure;//TIMPWM的

        RCC_APB1PeriphClockCmd(RCC_APB1Periph_TIM3,ENABLE);
        //使能TIM3的时钟线;

        //复位定时器
        TIM_DeInit(TIM3);

        //TIM_Prescaler:72,TIM_Period:20000周期为20ms
        TIM_TimeBaseInitStructure.TIM_Prescaler = -;                        //定时器周期
        TIM_TimeBaseInitStructure.TIM_Period = -;                        //定时器更新的重装载值0-65535
        TIM_TimeBaseInitStructure.TIM_CounterMode = TIM_CounterMode_Up;
        TIM_TimeBaseInitStructure.TIM_ClockDivision = TIM_CKD_DIV1;
        TIM_TimeBaseInit(TIM3,&TIM_TimeBaseInitStructure);            //初始化TIM3      

        TIM_OCInitStructure.TIM_OCMode = TIM_OCMode_PWM1;
        TIM_OCInitStructure.TIM_OutputState = TIM_OutputState_Enable;
        TIM_OCInitStructure.TIM_Pulse = ;                                //预设值
        TIM_OCInitStructure.TIM_OCPolarity = TIM_OCPolarity_High;    

        TIM_OC1Init(TIM3,&TIM_OCInitStructure);
        TIM_OC2Init(TIM3,&TIM_OCInitStructure);
        TIM_OC3Init(TIM3,&TIM_OCInitStructure);
        TIM_OC4Init(TIM3,&TIM_OCInitStructure);

        TIM_OC1PreloadConfig(TIM3,TIM_OCPreload_Enable);
        TIM_OC2PreloadConfig(TIM3,TIM_OCPreload_Enable);
        TIM_OC3PreloadConfig(TIM3,TIM_OCPreload_Enable);
        TIM_OC4PreloadConfig(TIM3,TIM_OCPreload_Enable);

        TIM_CtrlPWMOutputs(TIM3, ENABLE);
//        TIM_ITConfig(TIM3,TIM_IT_CC1|TIM_IT_CC2|TIM_IT_CC3|TIM_IT_CC4,ENABLE);
        //使能标志位CC1,CC2,CC3,CC4
        TIM_Cmd(TIM3,ENABLE);
        //使能TIM;
}

上面的TIM周期是20ms

三、修改PWM的方法

void TIM_SetCompare1(TIM_TypeDef* TIMx, uint16_t Compare1);
void TIM_SetCompare2(TIM_TypeDef* TIMx, uint16_t Compare2);
void TIM_SetCompare3(TIM_TypeDef* TIMx, uint16_t Compare3);
void TIM_SetCompare4(TIM_TypeDef* TIMx, uint16_t Compare4);